Battery Box.
Posted: Mon Feb 17, 2014 9:50 pm
Does anyone have the dimensions for the original battery box on the CA-1 ?
Clarkair CA-1 Discussion Board
A discussion board for the Clark CA-1 Bulldozer
http://clarkairdozer.com/message_board/
Battery Box.
http://clarkairdozer.com/message_board/viewtopic.php?f=5&t=133
Page 1 of 1
Re: Battery Box.
Posted: Thu Mar 13, 2014 9:37 pm
I'll have to reply to my own post about the battery box. I picked one up recently. Art
Re: Battery Box.
Posted: Fri Mar 14, 2014 7:57 am
Congratulations. Tough part to find.
Was it new or used?
Do you have a picture that you can post?
Was it new or used?
Do you have a picture that you can post?
Re: Battery Box.
Posted: Fri Mar 14, 2014 11:43 am
I will try. I can't seem to be able to access photos. I had sent Ken some pictures of my project, maybe I can send them to him again and post them that way. I,m sure that there is an easier way but I don't know how. Art
Re: Battery Box.
Posted: Fri Mar 14, 2014 7:14 pm
Thank you.
How to post pictures is in the board FAQ's.
viewtopic.php?f=3&t=48
They have to be hosted to use those directions.
or you can use the upload attachment tab directly below. Find the pic by file name on your PC and it is stored on the site.
Bill
How to post pictures is in the board FAQ's.
viewtopic.php?f=3&t=48
They have to be hosted to use those directions.
or you can use the upload attachment tab directly below. Find the pic by file name on your PC and it is stored on the site.
Bill
arts bat box
Posted: Sun Mar 23, 2014 10:59 am
Re: Battery Box.
Posted: Sun Mar 23, 2014 11:01 am
don nelsons box cover
Posted: Sun Mar 23, 2014 11:03 am
arts box dimensions
Posted: Sun Mar 23, 2014 11:08 am
sent to me By Art I thought i should pass it on
thanx ken
All stock is 1/16 inch thick.
Base; 1in. rise and 1-1/2 in. bottom.
10-1/8 in. x 7 in. outside measurement
this is made from one single piece of stock with a 7-1/4 in. by 4 in. cutout in center.
Top; 10-1/2 in. by 7-3/8 in. outside
7/8 in deep with 1/4 in lip
Flanges welded to side for hold down bolts and latch clip (see photo) I sent you
Top cover; 10 in. by 7 in. outside
1-1/4 in deep with cable flares to side (see photo)
Hinges; 1-1/4 in. wide welded to cover
thanx ken
All stock is 1/16 inch thick.
Base; 1in. rise and 1-1/2 in. bottom.
10-1/8 in. x 7 in. outside measurement
this is made from one single piece of stock with a 7-1/4 in. by 4 in. cutout in center.
Top; 10-1/2 in. by 7-3/8 in. outside
7/8 in deep with 1/4 in lip
Flanges welded to side for hold down bolts and latch clip (see photo) I sent you
Top cover; 10 in. by 7 in. outside
1-1/4 in deep with cable flares to side (see photo)
Hinges; 1-1/4 in. wide welded to cover
Re: Battery Box.
Posted: Sat Apr 11, 2015 4:03 pm
Well, I am new to the Clark restoration game. I now have one and am missing this box. I am adept as welding and fabricating but often it is better to see the drawing with the original dimensioned out. I am hoping someone will do that.
By the way, I am looking for parts so if there are any dozer guys who have spares, contact me here. Thanks
By the way, I am looking for parts so if there are any dozer guys who have spares, contact me here. Thanks